China charge controller,Competitive Price charge controller

What are the reasons for the sulfation of lead-acid battery plates?

Apr , 15 2023

The reasons for plate sulfation are as follows: 1) The initial charging of the battery is insufficient or the initial charging interruption time is long; 2) The battery is insufficiently charged for a long time; 3) Failure to charge in time after discharge; 4) Frequent overcharging or low current deep discharge; 5) If the density of the electrolyte is too high or the temperature is too high, lead ...

more

Damage of lithium battery caused by overcharge and discharge

Apr , 24 2023

The cathode materials of lithium-ion batteries are usually composed of active compounds of lithium, while the negative electrodes are carbon with special molecular structure. The main components of the common cathode materials are licoo2/LiFePO4, etc. When charging, the potential added to the battery poles forces the positive compounds to release lithium ions and embed the anode molecules into the...

more

Basic knowledge of filters

Jun , 21 2023

The Line filter is a filter circuit composed of capacitance, inductance and resistance. A filter can effectively filter out a specific frequency point in the power line or frequencies outside of that frequency point, obtaining a specific frequency power signal or eliminating a specific frequency power signal. A filter, as the name suggests, is a device that filters waves. Wave "is a very broad phy...

more

7 Factors to Examine While Choosing a Lithium-Ion Battery Charger

Jul , 20 2023

From confirming an acceptable input voltage to features like protection design and safe charging mode, these factors can help you select the right lithium-ion battery charger 1. Acceptable Input Voltage An input higher than the voltage sustenance capacity of the charger may cause damage to its internal components. Most countries use a battery charger design of the universal global voltage 110-230V...

more

Effect of temperature on the performance of lead-acid batteries

Sep , 18 2023

What are the effects of temperature on the performance of lead-acid batteries? From the chemical reaction equation of lead-acid batteries, PbO2 is on the positive plate, and Pb is on the negative plate. The electrical and physical properties of these two substances vary very little with temperature, so it can be said that the temperature effect of the discharge performance of lead-acid batteries i...

more

What is a nickel-cadmium battery

May , 31 2024

1. Working principle of nickel-cadmium battery Nickel-cadmium batteries are rechargeable batteries that convert chemical energy into electricity through REDOX reactions. It consists of a negative electrode (the negative material is Cd), a positive electrode (the positive material is NiOOH), and an electrolyte (the main component is KOH). 2. Features of nickel-cadmium batteries Long cycle life; Wid...

more

Maximum power point tracking algorithm for photovoltaic power generation

Jun , 22 2024

1. Introduction Photovoltaic power generation is a technology that uses solar energy to convert light energy into electricity. In the photovoltaic power generation system, in order to obtain the maximum power generation power, it is necessary to track the change of solar radiation intensity in real time, and adjust the working state of the photovoltaic module to keep near the maximum power point. ...

more

Analysis and application of charge and discharge curve of lithium battery

Jun , 27 2024

Abstract: In this paper, the analysis method of charge and discharge curve of lithium battery is introduced in detail, including charge efficiency, discharge characteristics, capacity evaluation, internal resistance evaluation and cycle life evaluation. Through the interpretation of the charge and discharge curve, the performance and characteristics of lithium batteries can be deeply understood, w...

more

What is the meaning of float charging for intelligent three‐stage charger in battery charger?

Jul , 12 2024

Float charging: Keep constant voltage charging, the charging current continues to decrease, and the battery is charged with maintenance type. When the charging current decreases to the set value or the charging time reaches the set value, the red light of sufficiency will be on, and the time will be about 2H, charging 10% of the power. Ordinary chargers are old‐fashioned chargers, charging, whethe...

more

Effect of electrolyte density and discharge on lead-acid batteries

Nov , 29 2024

(1) Electrolyte density under different geographical and climatic strips. Whether the electrolyte density is high or low, it is necessary to make a specific analysis for the specific situation. Winter temperature is low, the viscosity of the electrolyte is large, it is not easy to penetrate the inside of the plate, the end voltage and capacity of the battery will decline, especially in the strong ...

more

Lithium battery life The reason for the slow charging speed

Dec , 13 2024

1. Electrical problems: Insufficient power of the charger is one of the common reasons for slow charging speed. If the output current of the charger used is small and cannot meet the maximum charging current requirements of the battery, the charging speed will be limited. For example, a lithium battery mobile phone that supports fast charging, the original charger output current is 3A, and the cha...

more

Radio Frequency Interference Filters (RFI)

Apr , 03 2025

Chapter 1: Application Scenarios of RFI Filters in Industrial Chargers RFI Filter is a key component for solving high-frequency electromagnetic interference (EMI), which is especially indispensable in high power and high frequency equipment such as industrial chargers. Industrial chargers are often faced with complex electromagnetic environments: fast switching of switching power supplies, high-cu...

more

what are you looking for?

blog

blog